Drilling Push Pull Tools for Rig Floor Pipe Handling | Hand Safety First

HSF
Hand Safety First
Product Collection

Drilling Push Pull
Safety Tools

Purpose-built for rig floor operations — from tripping in and out to setback, racking, and connection alignment. Each tool delivers directed control of drill pipe movement at the points where hands typically have no business being.

10

Rig Floor Applications

Drill Pipe Handling

Controlled Movement

Hands-Free Operation

Offshore & Land Rigs

10 Products In Stock
Operational Context

Where Hands Get Exposed in
Drill Pipe Handling

Rig floor hand injuries don't typically happen because crews are cutting corners. They happen because precision is required at close range — and hands are the default tool for getting that precision. During normal drilling operations, there are four distinct points where floormens routinely place hands in positions of exposure.

01
Pipe Positioning During Tripping
During trips in and out, pipe stands must be guided from the mousehole or V-door to the rotary and into the elevator. The final few feet of positioning require hands to direct and stabilise the pipe — placing them between the stand and adjacent structures.
02
Setback and Rack Handling
Standing back pipe in the setback area and racking stands in the fingerboard requires directional control that can't be achieved from a safe working distance with bare hands. Floormens guide each stand into position, often with other pipe already racked alongside it.
03
Connection Alignment — Pin to Box
Aligning the pin end with the box end at the rotary requires hands to position and hold the pipe while the top drive or tongs engage. The connection point sits directly between two heavy, moving components — elevator above, rotary table below.
04
Pipe Rotation and Directional Control
During make-up and break-out, pipe must be held against the torque of spinning tools. Rotation control — stopping spin, redirecting drift, and positioning joints into tong range — typically requires hands on the pipe at the point of movement.
Method

Control Without
Hand Contact

The question isn't whether control is needed at those four points — it is. The question is whether that control has to come from bare hands at close range. HSF drilling tools are built around a single principle: the floorhand stays in control of the pipe, but from a position that is outside the pinch zone and clear of the line of fire.

This isn't about adding a safety step to the operation. It's about substituting the tool that delivers control — replacing the hand with something purpose-designed to do the same job from a better position.

Directed Pipe Movement from Distance
Each tool extends the operator's ability to push, pull, guide, or stabilise pipe without requiring hand contact at the hazard point. The handling task stays the same — the hand position changes.
Out of Pinch Zones and Line-of-Fire
Tools are designed around the specific geometry of each handling task — grip angle, pipe diameter, and direction of load — so that the tool engages at the hazard point while the operator's hands and body remain clear.
Consistent Handling Across Crews
Individual technique varies. How hard someone grips, when they let go, where they stand — these shift with fatigue, distraction, and experience level. Tools standardise the engagement point and body position, independent of who is on the floor.
No Disruption to Operational Tempo
HSF tools are built to fit within the existing handling sequence — not to add steps, slow the trip, or require additional personnel. They replace hand contact at specific moments; everything else proceeds as normal.
All Products 10 Items
HSF Pipe Wipe Tool - Hands Off Tools
01
In Stock
Hands Off Tools
HSF Pipe Wipe Tool - Hands Off Tools

Applies contact to the pipe OD during wiping operations without hand-to-pipe contact. Maintains consistent wipe pressure around the pipe circumference while the operator controls position and movement from outside the wiper's immediate zone.

View Product → In Stock
HSF Twist Control Tool - Hand Safety Tool
02
In Stock
Hand Safety Tool
HSF Twist Control Tool - Hand Safety Tool

Controls pipe rotation during connection make-up and break-out without hands on the spinning joint. Guides directional movement of the pipe as torque is applied, stopping spin-out and redirecting drift from a controlled handling position.

View Product → In Stock
HSF Rack Back Tool
03
In Stock
Drilling Tool
HSF Rack Back Tool

Positions drill pipe stands into the rack board finger slots at the derrickman level without requiring direct hand contact between adjacent stands. Guides the stand into its racked position with controlled lateral movement, keeping the operator clear of the fingerboard pinch zone.

View Product → In Stock
HSF Hand Safety Tools Storage Station & Starter Kit
04
Starter Kit
Storage & Kit
HSF Hand Safety Tools Storage Station & Starter Kit

Provides a designated storage and deployment point for HSF drilling tools on the rig floor. Keeps tools accessible at point-of-use across tripping, setback, and connection operations, supporting consistent tool deployment within the active handling zone.

View Product → In Stock
HSF Pipe Set Back Tool - Hand Safety Tool
05
In Stock
Push Pull Tool
HSF Pipe Set Back Tool - Hand Safety Tool

Positions drill pipe stands into the setback area on the rig floor during stand-building operations. Guides each stand into its standing position with directional control, without hands between the pipe and adjacent stands or floor structures.

View Product → In Stock
HSF Pipe Grab Tool
06
In Stock
Push Pull Tool
HSF Pipe Grab Tool - Push Pull Tools - Hand Safety First

Engages and controls the pipe at the rig floor during tripping, allowing the floorhand to push, pull, and position the drill pipe stand without hand contact at the rotary table or elevator zone. Maintains directional grip on the pipe through the full range of floor-level handling.

View Product → In Stock
HSF Drill Pipe Handling Tool
07
In Stock
Push Pull Tool
HSF Drill Pipe Handling Tool - Push Pull Tool - Hand Safety First

Controls drill pipe during tripping operations from pickup to placement. Allows the floorhand to direct and stabilise pipe movement at the rotary level while maintaining a working position that is clear of the elevator link travel path and the top of the rotating assembly.

View Product → In Stock
HSF Drill Pipe Connection Guide
08
In Stock
Hands Off Tools
HSF Drill Pipe Connection Guide - Hands Off Tools - Hand Safety First

Guides pin-end alignment into the box end at the connection point during tripping operations. Positions the pipe for thread engagement without hands between the two joints, eliminating hand contact at the most confined and highest-consequence point of the make-up sequence.

View Product → In Stock
HSF Drill Pipe Casing Tool
09
In Stock
Push Pull Tool
HSF Drill Pipe Casing Tool - Push Pull Tool - Hand Safety First

Handles and positions casing string during run-in operations at the rotary. Controls pipe body movement as each joint is lowered and landed in the slips, allowing hands-off guidance through the landing zone where casing weight and movement create the highest exposure.

View Product → In Stock
HSF Cargo Handling Tool
10
In Stock
Push Pull Tool
HSF Cargo Handling Tool - Push Pull Tool - Hand Safety First

Pushes and pulls cargo items across the rig deck and floor without hands at the leading edge of the load. Provides directional control of skids, equipment boxes, and loose gear during deck handling, keeping hands clear of crush zones between the load and fixed structures.

View Product → In Stock
Product Design

Designed for
Rig Floor Operations

The rig floor is not a controlled environment. Tools used there have to work in wet conditions, under time pressure, by crews who are handling heavy equipment at pace. HSF drilling push pull tools are built to that standard — not to a lab standard, not to a light-industrial standard.

⚙
Built for Real Drilling Environments
Designed to function on an active rig floor — wet decks, oily pipe, gloved hands, and limited space. No modifications or adaptations required for standard drilling operations.
⬡
Multiple Handling Points on a Single Rig
The HSF range covers the full pipe handling cycle — floor level, setback, fingerboard, connection, and casing — so that controlled handling is available at every point where hands are typically used.
↔
Repeatable, Consistent Pipe Handling
Tools standardise how handling tasks are performed across shift changes and crew rotations. The contact point, body position, and engagement method remain consistent regardless of who is on the floor.
◈
Fits Within Existing Workflows
HSF tools are deployed at specific moments within the existing operational sequence. They don't require procedure rewrites or additional personnel — the workflow stays the same, the hand position changes.
Frequently Asked Questions

Drill Pipe Handling
Tool Questions

Drill pipe handling tools are used to position, guide, and control drill pipe movement on the rig floor during tripping operations, connection make-up and break-out, setback, rack-back, and casing runs — without requiring direct hand contact at pinch points or in the line of fire. They replace hand contact at specific moments in the handling sequence, not the sequence itself.
HSF drilling tools are used at multiple handling points across the rig floor: the rotary table area during tripping, the V-door and pipe ramp during pipe pickup, the setback area during stand building, the rack board level for racking back stands, and at the connection point during make-up and break-out. The full range covers each of these points without requiring the same tool to do everything.
Each HSF tool is designed to extend the operator's reach and control to the pipe at a safe distance. They allow directional control of pipe movement — pushing, pulling, guiding, and stabilising — while the operator remains outside pinch zones and line-of-fire positions. Control is maintained; hand contact at the hazard point is not.
Yes. Several HSF tools are specifically built for tripping in and out. The HSF Drill Pipe Handling Tool and HSF Pipe Grab Tool provide directional control and positioning of pipe stands at the rotary during trips, allowing floormens to guide pipe into the slips and elevator without placing hands near the rotary or elevator links.
Hand exposure during pipe handling is typically not the result of unsafe behaviour — it happens because precise control is required at close range. HSF tools replicate that control from a safe working position. For example, the HSF Drill Pipe Connection Guide aligns the pin and box end at the connection point without the floorhand placing hands between the two joints during make-up.
Yes. HSF drilling push pull tools are designed for rig floor use across land and offshore drilling environments. They are built to function in the physical conditions typical of an active rig floor — including tight working space, wet or oily surfaces, and high-frequency operational repetition across back-to-back shifts.
No. HSF tools are built to integrate into existing handling workflows without adding steps or changing the operational sequence. They replace hand contact at specific points in the task — not the task itself. Crews typically reach consistent, repeatable handling performance within normal operating tempo.
Yes. The HSF drilling tool range is designed to cover multiple handling points across a single operation. The HSF Hand Safety Tools Storage Station & Starter Kit provides a structured starting point for equipping a rig floor with the tools most commonly needed across tripping, setback, connection, and racking operations.
Get in Touch
Discuss Your
Drilling Application

Whether you're equipping a single rig floor or standardising across a fleet, HSF can help identify the tools that fit your specific handling operations. No generic recommendations — application-specific guidance only.

Request Product Details Build Your HSF Tool Kit View All Products

 

Back to blog

Leave a comment

Please note, comments need to be approved before they are published.